Nitecore Torches and Batteries

Description The Nitecore NPB1 Waterproof Power Bank is your ideal power solution for outdoor activities and everyday carry. IP68 rated and waterproof up to 2m, with 1m of drop resistance, NPB1 can take a splash or an accidental drop when you are running, hiking, trekking or kayaking. Carry the NPB1 with confidence no matter where you go. At 4.03 inches long and just 3.7oz you won't even notice the NPB1 in your pocket, or attached to your bag by its hanging loop. Travelling? NPB1 has multiple protection safeguards including overcharge, short-circuit, and thermal protection and is in accordance with flight regulations, you can keep it with you wherever you go. NPB1 can quickly charge almost any device on the go with QC 3.0 support and 18 W of max output. Never get caught off guard with a dead power pack again, thanks to the touch sensor power display. Key Features: 5000mAh capacity can fully charge a phone Recommended power source for HU60 IP68 Rated waterproof and dust resistant Touch sensor power level indicator display QC 3.0 output with a max of 18W Specifications Battery Type: 21700 Li-ion Battery Capacity: 5000mAh Input: Micro-USB: 5V-2A Output: USB-A: 5V-2.4A 9V-2A (18W MAX) IP Rating: IP68 Dimensions: L-4.03" x W-1.06" x H-1.06" Weight: 3.7oz

Read more less

Description Introducing the upgraded Nitecore TINI 2: the dual OSRAM P8 LEDs give off an impressive 500 lumen output, perfect for daily use for a far-reaching and uniform beam that reaches up to 97 yards. For how powerful the TINI 2 is, Nitecore managed to keep it small and lightweight. Weighing less than 1oz and smaller than a car key, TINI 2 is the perfect everyday carry light on a keychain. Featuring an OLED display, this screen shows real-time information like brightness level, mode, lumen, battery voltage, and remaining runtime. The display takes out the guessing game of knowing when your battery needs to charge. When it's time to charge, the TINI 2 is no slouch with rapid USB-C charging. The TINI 2 is a must-have EDC flashlight on a keychain. The Nitecore TINI 2 is packed with features that make it ideal for everyday carry. Its dual switch design allows you to easily power on and off or adjust the brightness level. Hold the mode button to directly access the turbo mode or hold the power button for the ultralow. It further prevents accidental activation with a half lockout mode or full lockout mode. To meet different usages, the Tini 2 comes with two user modes: the demo mode is designed for short-bursts of illumination while the daily mode is optimized for longer sustained illumination. With all of the new features and upgrades, the Tini 2 is a great addition to any EDC collection. Specifications LED 2x OSRAM P8 Maximum Brightness 500 lumen Peak Beam Distance 97 yards Peak Beam Intensity 2000 cd IP Rating IP54 Impact Resistance 1 m Dimensions L-1.83"xW-0.98"xH-0.49" Weight 0.66oz Brightness Output by Mode Turbo Output: 500 lumen Runtime: 15 min High Output: 200 lumen Runtime: 45 min Mid Output: 65 lumen Runtime: 2.5 hr Low Output: 15 lumen Runtime: 8 hr Ultralow Output: 1 lumen Runtime: 60 hr

Read more less

Description The NITECORE HC35 L-shaped headlamp is the first next generation headlamp to feature a high performance 21700 battery. This powerful battery unleashes the quad LEDs max brightness of 2700 lumens turbo with over 146 yards of beam throw. The quick detach headlamp bracket allows you to easily rotate the flashlight on the headband to illuminate where you need it. Key Features: CONVENIENT BATTERY OPTIONS The NITECORE HC35 comes with a high performance, 4000mAh 21700 li-ion battery that provides up to 1200 hours of uninterrupted operation. It can also run on any >8 high discharge 18650 battery, a pair of CR123, or RCR123 batteries when you use included battery adapter sleeve. With a built-in micro USB charging port, and LED power indicator, the HC35 will not leave you in the dark when paired with a rechargeable battery. VERSATILE L-SHAPE DESIGN When removed from the bracket the multipurpose, 90 degree design allows the headlamp to double as a handheld flashlight or worklight. Enjoy hands-free illumination with the magnetic tailcap, while the removable pocket clip provides simple carry options. Specifications Max Output 2700 Lumens Max Beam Distance 134 m Max Beam Intensity 4500 Max Runtime 1200 h 0 m / 50 d LED 4 x CREE XP-G3 S3 LED Reflector SMO Battery 1 _ 18650 ,2 _ CR123 ,2 _ RCR123,1 _ 21700 Special Modes Location Beacon,SOS,Strobe Beam color White light Length 128.2 mm / 5.04 in Weight 138.5 g / 4.88 oz Activity Gear,Outdoor/Camping

Read more less

Description The Nitecore NL1485 14500 Rechargeable Lithium-Ion Battery (3.7V, 850mAh) has a capacity of 850mAh, 3.7V of output power, a rating of 3.15Wh, and a continuous discharge rate of 0.8A. Because of its high capacity, this battery is suitable for high-drain devices, and it has a built-in chip that protects against excessive charge/discharge and short-circuits. The nickel-plated and stainless steel protectors provide high-impact resistance and the metallic wrapper guards against abrasion. It features pressure relief valve protection and has a built-in PTC to protect against rapid temperature increases and high current surges. The anode design of the battery also has a high heat resistance, and the microporous barrier protects the delicate components inside. To charge the battery, use any of Nitecore's compatible smart chargers. Specifications Battery Battery Type 1 x 14500 Battery Chemistry Li-Ion Battery Voltage 3.7 V Capacity (mAh) 850 mAh Capacity (mAh) Typical: 850 mAh Capacity (Wh) 3.15 Wh Maximum Recharge Cycles 500 Battery Dimensions ¿: 0.6 x L: 2.1" / ¿: 15.2 x L: 53.3 mm Battery Weight 0.74 oz / 21 g General Certifications COE, RoHS, as per Manufacturer

Read more less

Description Note: Product does not include batteries Nitecore's versatile and compact MH27UV Multi-Spectrum LED Flashlight is as powerful as larger search lights yet fits comfortably in your hand. This illuminator uses a white Cree XP-L HI V3 primary LED to produce four outputs from an energy-saving 1 lumen minimum output, to a darkness-piercing 1000-lumen turbo. In addition to the white emitter, there is an array of secondary-coloured LEDs - blue, red, and ultraviolet - set around the main reflector that provide coloured light to perform tasks without interfering with night-adjusted vision. Adding to the MH27UV's versatility are three strobe modes and three coloured flashing modes that can be used for everything from directing traffic to sending a distress signal. The light is designed with tactical professionals in mind. It has a two-stage pushbutton tailcap switch with momentary and constant-on modes. This switch has last-mode-memory for the primary outputs and strobe mode so you can set the output ahead of time and go right to that intensity or mode immediately. For special situations, users have instant access to both the UV LED light and 1000-lumen Turbo output for chequing IDs and lighting large areas or to search. An included tactical ring can be installed on the handle to help facilitate various pistol/light grip techniques. Complementing the multiple light outputs is a housing that is built to withstand years of use. Its aluminium alloy body has a scratch and corrosion-resistant Type III hard anodised finish, with a scratch-resistant tempered reflector window that has an anti-reflection coating to maximise light transmission. The light is impact-resistant and IPX8-rated, making it fully submersible to a depth of over 6.5 feet. Heat diffusing fins built into the head provide passive overheat protection, while heat-management circuitry automatically monitors and adjusts the output and performance to prevent damage to the light. This flashlight includes a quality USB charger, holster, clip, tactical ring, lanyard, spare charging port cover, spare O-ring and a spare tailcap cover. Key Features: Performance White light: Low: 1 lumen Moed: 55 lumen High: 250 lumen Turbo: 1000 lumen Coloured light: Blue: 3 lumen Red: 13 lumen UV: 500mW @ 365nm One primary white Cree XP-L HI V3 LED One each - Blue/Red/UV - secondary LEDs Blue LED: Highlights fluids such as blood for tracking Red LED: Illuminates without affecting night adjusted vision to read or perform tasks UV LED: Use for authenticating money, IDs, etc. and fluorescence activation Smooth aluminium reflector produces a bright centre cone of light with large, dimmer peripheral ring Special Modes Disorientating strobe mode SOS distress signal: Automatically cycles through Morse code sequence Location beacon: Emits a slow steady flash to signal location "Police" warning signals: Mode 1: Alternates between Red and Blue LEDs to simulate police lights Mode 2: Flashing Red LED only Mode 3: Flashing Blue LED only Switching Type: Pushbutton Location: Tailcap and Body Tailcap: Controls on/off with last mode memory for primary outputs and strobe mode Body: Dual switches control output intensity and mode selection Momentary and constant-on activation Instant access to Turbo output and Red LED Charge Time 6 h with one 18650 Li-ion battery installed Construction Aluminium alloy Waterproofing IPX8-rated, submersible to 6.6' / 2.0 m for up to 30 minutes Impact Resistance Yes Dimensions Head: 1.6" / 4.0 cm Handle: 1.0" / 2.5 cm Length: 6.1" / 15.4 cm Weight 6.0 oz / 170.0 g, without battery

Read more less

Description The new NITECORE UM2 is a QC input available, intelligent USB dual-slot charger, with a total max output of 3,000 mA and a single slot max output of 1,500 mA and is capable of charging 2 batteries simultaneously and controlling each slot independently. It only takes 2 hours to charge 80% of a 3,500mAh battery. The LCD screen can display a real-time information of Charging Current, Battery Voltage, Charged Volume and Charging time. It can enable an automatic detection of battery power level and automatic selection of the appropriate voltage and charging mode and automatic selection between 3 charging modes (CC, CV and -dV/dt). The charging parameters can be set manually to meet various charging needs. The specially designed Micro USB port is compatible with various mobile power source, solar panel and USB adaptors to ensure endless power supply. UM2 incorporates an optimized IMR battery charging program, which is able to monitor the entire charging process, ensuring that the cut-off voltage is always within safe limits to extend the lifespan of the batteries. The UM2 is compatible with 3.6V/3.7V Li-ion rechargeable batteries, 3.8V Li-ion rechargeable batteries, 1.2V Ni-MH/Ni-Cd rechargeable batteries and 3.2V LiFePO4 batteries. Multiple safeguards ensure the safe charging process, including anti-short circuiting and reverse polarity protection, overtime charging protection, over-discharged Li-ion battery activation and over-discharged IMR battery restoration. Apart from being constructed from durable and fire retardant PC materials, the built-in temperature regulation system is designed to prevent the overheat and to ensure the stability of the charging process. If there is no action to the buttons or batteries in 10 minutes, the screen will automatically go dim to save energy. Key Features: QC 2.0 input available Total max output of 3000 mA with single slot max output of 1500 mA LCD display for real-time charging information USB charging port for outdoor charging Intelligent charging mode selection Energy saving function Compatible with Li-ion and Ni-MH /Ni-Cd batteries with automated detection

Read more less

Description With an outstanding water and dust resistance, the Nitecore NPB4 Waterproof Power Bank is the latest model of the world's first IP68 rated waterproof power bank series and remains unaffected after 2-meter underwater submersion for 30 minutes, perfect for caving, mountaineering, maintenance checks and more. The premium waterproof design includes the high strength waterproof O-ring on the charging port, the advanced glue pouring technology to ensure a waterproof environment for components and the fire retardant PC materials constructed shell by ultrasonic welding technology to offer extreme tightness against water and vapor. The solid housing constructed by the lightweight and fire retardant PC materials has an excellent high temperature, scratch and impact resistance to guarantee a long lifespan. Equipped with 4 x 21700 Li-ion batteries, the NPB4 has a sufficient power of 20,000mAh for smartphones, GPS, headlamps, headphones and more. Featuring long lifespan, high energy density and powerful performance, 21700 Li-ion batteries were first introduced in the electric car industry and are considered to be the future of cylindrical batteries. It is ultra compact and lightweight with 378g (13.33oz). The included high strength nylon holster makes it portable and easily attached to the backpack or the MOLLE System. The USB-C + Dual USB-A output design makes the charging process incredibly convenient with a max output power of 18W. The NPB4 has a touch sensor power level display. Tap the Touch Icon, and the blue indicators beside the input port will be turned on to display the power level. The NPB4 is equipped with multiple protection safeguards to be used in temperature between -1040? (14104?). In accord with the UN38.3 Standard with a rated capacity less than 100Wh, the NPB4 is airline approved as your best worry-free power companion while on the move.  Key Features: 2m Submersible With outstanding water and dust resistance, the NPB4 remains unaffected after 2 meter underwater submersion for 30 minutes, perfect for caving, mountaineering, maintenance, checks, and more Premium Waterproof Design High strength waterproof O-ring on the charging port Advance glue pouring technology to ensure a waterproof environment for components. Fire retardant PC materials constructed shell by ultrasonic welding technology to offer extreme tightness against water and vapour. Touch Sensor Power Level Display Tap the touch icon, and the blue indicators beside the input port will be turned on to display the power level Specifications Battery Type 21700 Li-ion Batteries Capacity 20,000mAh 3.64V (72.8Wh) Rated Energy 12,400mAh 5V (TYP 1A) Input Micro-USB: 5V?2.4A 9V?2A, USB-C: 5V?3A 9V?2A 12V?1.5A Output USB-A: 5V?3A 9V?2A 12V?1.5A, USB-C: 5V?3A 9V?2A 12V?1.5A Multi Ports 5V?3A IP Rating IP68

Read more less

Description The 3.7V, 650mAh RCR123A Li-Ion Rechargeable Battery from Nitecore is designed to deliver consistent power throughout the charge-cycle for use in high-drain devices. Integrated short-circuit, over-charge, and over-discharge circuitry help maintain its performance. A built-in pressure relief valve provides further protection. The battery can take up to 500 full charging cycles, offering an economic and environmentally-friendly alternative to disposable batteries. NOTE: not suitable for use with Arlo cameras. Specifications Chemistry Li-Ion Capacity 650 mAh Output Voltage 3.7V Dimensions 1.4 x 0.7" (3.5 x 1.7 cm) Weight 0.6 oz (17.8 g)

Read more less

Description Offering five brightness levels of white light, a red and auxiliary white light, and SOS, beacon and strobe modes, Nitecore's HC65 USB-Rechargeable LED Headlamp is a versatile and powerful illumination tool. Its main emitter is a Cree XP-G2 S3 LED with a maximum output of 1000 lumens and a maximum runtime on low power of 800 hours. It also has a second, 26-lumen white light with a high Colour Rendition Index for tasks like reading that don't need as much candlepower, and a red light that preserves night-acclimated vision for night photography, astronomy or wildlife observation. The main light shines in a wide 100¡ cone, and the lamp can be tilted 180¡ to put the beam right where you need it. The lighting programme features ultra-low, low, medium, high, and turbo white; auxiliary white; steady and flashing red; and 1000-lumen white SOS, beacon and strobe modes. The hard-anodised aluminium housing is IPX8-rated waterproof and submersible to 6.6' and impact-resistant to 5'. A protective cap keeps moisture and dirt of the intelligent micro-USB charging port. The Precision Digital Optics Technology reflector produces a smooth, even beam, and Advanced Temperature Regulation technology offers safety and comfort. Along with a rechargeable 18650 battery, the light can also run on two non-rechargeable CR-123 batteries if need be. A built-in indicator shows how much power is left in your battery to avoid unpleasant surprises. Key Features: Light Performance Cree XM-L2 U2 1/80/280/550/1000 lumens 11-lumen red light 26-lumen high-CRI light mimics morning sunlight for accurate colours and low eye-strain PDOT reflector for smooth, even beam Use and Handling Wide 100¡ flood cone of light Constant-on, SOS, location beacon, strobe, flashing red Status indicator Runtime: 1 to 800 hours 180¡ adjustable lamp tilt Construction Aluminium housing Constant circuit (not pulse width modulation) for flicker-free performance Advanced Temperature regulation technology Intelligent micro-USB charging port Single push-button IPX8-rated waterproof, submersible to 6.6' Impact-resistant to 5' drops Specifications Illumination Source 1 x Cree XM-L2 U2LED Output White Light Ultra-Low: 1 lumen Low: 80 lumens Moed: 280 lumens High: 550 lumens Turbo: 1000 lumens Red Light 11 lumens Auxiliary White Light 26 lumens, CRI >90 Beam Width 100¡ Battery / Runtime One 3.7 V 3400 mAh 18650 battery: White Light Ultra-Low: 800 h Low: 16 h Moed: 4.8 h High: 2.8 h Turbo: 1 h Red Light 20 h constant-on, 32 h flashing Auxiliary White Light 25 h Charge Time 7 h Impact Resistance 4.9' / 1.5 m Weather Resistance IPX8, waterproof, submersible to 6.6' / 2 m Dimensions 3.3 x 0.7" / 8.4 x 1.8 cm Weight 2.2 oz / 63 g

Read more less

Description This Nitecore NL2150 5000 MAH Rechargeable Li-Ion Battery cell is specifically designed to be used with high performance flashlights and specialty electronics. The high capacity of 5000mAh allows your device to have long efficient run times. Protected with integrated overcharging and discharging circuitry, you can be sure that your battery will be safe through charging cycles and extended use. The lithium-ion chemistry not only provides stable, reliable power, but it also allows for recharging up to 500 cycles! Rechargeable batteries save you money in the long run and help the environment at the same time. Key Features: High performance battery for specialty electronics and lights 3.6V of reliable Li-ion power 5000mAh capacity for long run times Rechargeable up to 500 times 3 Year stable shelf life Overcharge and discharge protection circuitry CE and RoHS Certified Specifications Capacity 5000mAh Voltage 3.6V

Read more less

Description This 3.7V, 2600mAh 18650 Li-Ion Rechargeable Battery from Nitecore has been specifically designed for use in high-drain devices, and features integrated overcharge and over discharge protection circuitry which reduces the risk of damage to the battery. Its positive terminal is a conventional 'button' configuration to be compatible with most devices. Specifications Chemistry Li-Ion Capacity 2600 mAh Output Voltage 3.7 V Watt Hours 9.6 Wh

Read more less

The small Nitecore 18350 is a 3.7 volt, 700mAh 16340 rechargeable li-ion battery. You may charge these batteries over and over for years to come with a rating of more than 500 charge-discharge cycles. This is a button top cell making it easier to use with many flashlights.

Read more less

10000mAh capacity can charge a modern phone 2 timesCarbon fiber frame and panelsDual output channels USB and USBCLED remaining power level indicatorOne touch low current mode for delicate electronics5.29 oz - 40% lighter than conventional powerbanksIncluded in the BoxNITECORE NB10000 PowerbankUSB Cable (USB to USB-C)

Read more less

The new Nitecore P30i is a serious player. By stacking a large format rechargeable battery and a large reflector, you're looking at 1 kilometer range and 2000 lumens of light.From the moment you open the well designed packaging you'll see the work thats gone into this grunty work torch.Nitecore include a remote switch too if you plan to mount it.Also includes a insert sleeve so you can use 18650 batteries too.Using USB-C means much faster charging times (Cable included). Have a look around, the 5000 mAh battery is in the top range of capacity and output.Lets look at the beam profile. The 50mm reflector and its depth work like a speaker cone does for sound. For a hand held torch this size, its outputs are nuts.Max Output 2000 LumensMax Beam Distance 1000 mMax Beam Intensity 250000 cdMax Runtime 100 h 0 m / 4.16 dLED CREE XHP35 HI LEDBattery 1 × 21700, 2 × CR123, 2 × RCR123Special Modes Location Beacon, SOSLength 177.5 mm / 6.99 inHead Size 65 mm / 2.56 inWeight 255.5 g / 9.01 ozFeature Rechargeable, Ultra Long RangeActivity Hunting, Search, Outdoor/Camping, SAR(search and rescue)

Read more less

Nitecore is bringing back the classic, long handle, ultra-long throw flashlight back in style with the MH40S. The 1500 lumen max MH40S is equipped with a Lumingen G9 LED capable of a beam throw of over 1640 yards, almost a full mile! The newly designed remote pressure switch can be secured to any platform with multiple included accessories. The MH40S comes with all the accessories to be a dedicated hunting flashlight, patrol light, or search and rescue beacon. LONG THROW FLASHLIGHT - 1500 lumen output, over 1640 yards of throw - indispensable for hunting, work, on patrol, or for caving and hiking. USB-C RECHARGEABLE - With the built in USB-C fast charging port, the light can run over 105 hours. REMOTE PRESSURE PAD - Innovative pressure pad with multiple attachment options, velcro pad, picatinny rail adapter, or hook-and-loop straps while still use the tailcap switch. HEAVY DUTY FLASHLIGHT - Scratch resistant lens coating, HA III grade finish on a rough aero grade aluminum body, that is rated IP68 waterproof. Content - MH40S Rechargeable flashlight, charging cable, charger, holster, remote pad, picatinny rail and hook and loop attachments and a LumenTac Organizer. Specifications Weight 245.8 g Run Time Turbo 1500 lumen 3h15m ; High 500 Lumen 7h15m ; Mid 150 lumen 25h, Low 18 lumen 105h Lumens 1500 lumens Range 1499 meters Length 256 mm Peak Beam Intensity 570000 cd Tube diameter 25.8 mm Head diameter 65 mm

Read more less

Both NiteLab and NITECORE belong to SYSMAX which is dedicated to exploring LED technology to reinvent the flashlight LED solutions. NiteLab cooperates with an industrial partner to jointly develop the UHI LED Series, specially designed for flashlights. Featuring high light density and high beam intensity, the UHI LED utilizes the round light emitting surface (LES) to achieve an optimal lighting effect and beam distance, which challenges the impossible and begins a new era of the flashlight LED. Max Output 3,300 Lumens Max Beam Distance 505m Max Beam Intensity 63500 cd Max Runtime 650 h 0 m / 27.08 d LED NiteLab UHi 40 LED Reflector SMO Battery 1 × 21700, 2 x CR123/RCR123 Special Modes Strobe Beam color White Light Length 138.5 mm / 5.45 in Head Size 26.8 mm / 1.06 in Weight 82 g / 2.89 oz Feature Rechargeable, Tail Stand Activity Search, Outdoor/Camping, Emergency

Read more less

Description The 8Nitecore TIKI GITD Glow in the Dark Keylight* is a compact keychain flashlight made of a durable, glow-in-the-dark plastic that makes finding your keys easier than ever before. Enjoy up to 300 lumens of bright white light, or utilize the two UV and high-CRI (= 90) side LEDs. The 130mAh internal battery pack holds up to 40 hours of runtime, and charges up quick in a mere 80 minutes with a micro-USB cord. Rated IP66 waterproof and 1m drop resistant, your new TIKI GITD is ready for anything. Specifications Max Output 300 Lumens Max Beam Distance 71 m Max Beam Intensity 1260 cd Max Runtime 40 h 0 m / 1.66 d Battery Rechargeable Li-ion Special Modes UV Light Length 55 mm / 2.17 in Head Size 14.7 mm / 0.58 in Weight 12 g / 0.42 oz Feature Rechargeable Activity Outdoor/Camping

Read more less

Description Named for its small size, the Thumb Rechargeable LED Key-Chain Flashlight from Nitecore offers a lot of functionality for a light that weighs less than one ounce. It has both white and red LEDs with a top output of 85 lumens, and a head that tilts 120¡. The Thumb will run 45 minutes at high power and 22 hours at low power on a single charge. There's one button for the white LEDs and another for the red. Click the upper switch to activate the white lights and cycle through the high, medium, low and blinking modes: click the lower button to toggle between the red LED's constant-on and blinking. Pressing both buttons at the same time puts the light in lockout mode, so it won't be activated accidentally. To remove lockout mode, press both buttons again. Nitecore has included over-discharge, overcharge, and short-circuit protections in the Thumb, as well as a power indicator that blinks when the light is charging and shines green when it's charged. The housing is made of durable polycarbonate, and the light's clip allows you to wear it on a belt, a pocket, a pack strap, a hat, etc. Key Features: White and red LEDs Dual pushbutton switching 120¡ adjustable head Micro-USB rechargeable Specifications Output Low: 2 lumens Moed: 30 lumens High: 85 lumens Battery Built-in 3.7 V, 220 mAh lithium-ion Runtime Low: 22 h Moed: 2.25 h High: 45 min Housing Polycarbonate Dimensions 2.9 x 0.9 x 0.6" / 74 x 24 x 16 mm Weight 0.9 oz / 25 g

Read more less

4000 LUMEN FLASHLIGHTThe NITECORE P20iX is unrivaled when it comes to performance. Nitecore took the popular P20i frame and maintained the compact size, ergonomics, and doubled the power with four LEDs. This flashlight outputs a 4000 lumen floodlight that can reach up to 221 meters.USB-C RECHARGEABLE, EXTENDED RUNTIMEThe P20iX is part of Nitecore's iSeries using intelligent 21700 batteries. This enables a potently efficient output, granting 30 minutes of 4000 lumen burst and a max runtime of 350 hours on low. Fast recharge the P20iX via its built-in USB-C port. It can also be powered by 2x CR123A batteries as a backup.READY FOR DUTYDesigned for law enforcement and military users, enjoy instant turbo, instant strobe, six brightness modes and two programmable user modes. Nothing can hold the P20iX back when it can shatter through with its steel bezel with silicone nitrided glass breaking inlays. Included is a NTH20 holster that is compatible with duty belts and MOLLE systems. The P20iX is an ideal choice for security, police, or military personnel.Max Output 4000 LumensMax Beam Distance 221 mMax Beam Intensity 12200 cdMax Runtime 350 h 0 m / 14.58 dLED 4 x CREE XP-L2 V6 LEDsBattery 1 × 21700i, 2 × CR123Special Modes StrobeBeam color White LightLength 141.5 mm / 5.57 inHead Size 31.8 mm / 1.25 inWeight 116 g / 4.09 ozFeature STROBE READY, RechargeableActivity Gear, Search

Read more less

Description The defining characteristic of the Nitecore MT21C Periscope Torch is the tilting emitter head. In the 0¡ (straight) orientation it looks and is used like a conventional flashlight, but tilt the head 90¡ forward and it converts into a right-angle task or tactical light. This tilting can be done with a single finger for easier use and handling. Designed to withstand the rigors of everyday use, the body is made of a lightweight and durable aluminum alloy that is treated with a scratch-resistant hard-anodized finish. It is O-ring sealed to be waterproof and submersible to over six and a half feet, and impact-resistant to over three feet. Nitecore designed the light with a magnetic base and an integrated hang loop to add even more versatility to an already versatile light. Leaving your hands free for tasks, it also allows you to point the beam right where you need it. The head of this clever little 105-lumen torch swivels 180¡ and tilts 90¡, and the light is equipped with a belt/pocket clip and a hanging loop. On-off switching and brightness selection is controlled by a push button on the head. Key Features: 1/50/190/400/1000 Lumens One CREE XP-L HD V6 LED SOS, Location Beacon, Strobe Functions Adjustable 90¡ Tilting Head Side Activation Push-Button Switch Hard-Anodized Aluminum Alloy Body Impact Resistant and Submersible Hang Loop and Magnetic Base Integrated Power Level Indicator Runs on One 18650 / Two CR123 Batteries Specifications Max Output 1000 lumens Max Beam Distance 184 m Max Beam Intensity 8500 cd Max Runtime 700 h 0 m / 29.16 d LED CREE XP-L HD V6 Battery 1 _ 18650 ,2 _ CR123 ,2 _ RCR123 Beam color White light Length 131 mm / 5.15 in Head Size 25.4 mm / 1 in Weight 103.5 g / 3.65 oz

Read more less

The Nitecore NU35 (NU35) released in 2020. It uses Cree XP-G3 LED, TIR reflector and integrated 590mAh Li-Ion battery and 3 x AAA battery. The powerful emitter in this headlamp provides up to 460 lm output, 580 cd intensity, and a beam distance of 48 m. Max Output 460 Lumens Max Beam Distance 48 m Max Beam Intensity 580 cd Max Runtime 340 h 0 m / 14.16 d Battery Rechargeable Li-ion, 3 × AAA Special Modes Location Beacon, SOS, Warning Flashing Beam color White Light, Red Light Length 61.3 mm / 2.41 in Weight 79.5 g / 2.80 oz Feature Rechargeable Activity Outdoor/Camping, Industrial

Read more less

Nitecore is bringing back the classic, long handle, ultra-long throw flashlight back in style with the MH40S. The 1500 lumen max MH40S is equipped with a Lumingen G9 LED capable of a beam throw of over 1640 yards, almost a full mile! The newly designed remote pressure switch can be secured to any platform with multiple included accessories. The MH40S comes with all the accessories to be a dedicated hunting flashlight, patrol light, or search and rescue beacon. LONG THROW FLASHLIGHT - 1500 lumen output, over 1640 yards of throw - indispensable for hunting, work, on patrol, or for caving and hiking. USB-C RECHARGEABLE - With the built in USB-C fast charging port, the light can run over 105 hours. REMOTE PRESSURE PAD - Innovative pressure pad with multiple attachment options, velcro pad, picatinny rail adapter, or hook-and-loop straps while still use the tailcap switch. HEAVY DUTY FLASHLIGHT - Scratch resistant lens coating, HA III grade finish on a rough aero grade aluminum body, that is rated IP68 waterproof. Content - MH40S Rechargeable flashlight, charging cable, charger, holster, remote pad, picatinny rail and hook and loop attachments and a LumenTac Organizer. Specifications Weight 245.8 g Run Time Turbo 1500 lumen 3h15m ; High 500 Lumen 7h15m ; Mid 150 lumen 25h, Low 18 lumen 105h Lumens 1500 lumens Range 1499 meters Length 256 mm Peak Beam Intensity 570000 cd Tube diameter 25.8 mm Head diameter 65 mm Included Accessories: • 2 x 21700 Li-ion Batteries (NL2150 5,000mAh) • Wireless Remote Switch • QC Adapter • USB-C Charging Cable • Spare O-Ring and Lanyard • Hook and loop Fastener • 2 x hook and loop straps • Holster • NFR65 FIlter (RED) • NFG65 Filter (GREEN) • Gun Mount (Optional GM02MH/GM05) • 2 x Picatinny Rail Mounts (Optional)

Read more less

Nitecore is introducing their first ever intrinsically safe explosion proof headlamp. Designed for use in harsh environments, the EH1 comes with a TWO high capacity rechargeable battery installed and is rated at an IPX68 for dust and waterproofing. With a powerful CREE XP-G2 S3 and four red LEDs, this headlamp is versatile and durable. Use it for mining, underground and offshore petroleum exploitation, petrochemical and chemical industries, and other high risk industries. Note: The internal batteries of the EH1 have been specially designed to offer up to 1200 charging cycles comparing to typical rechargeable 18650 batteries offer only 500 recharging cycles. Specifications: LED: CREE XP-G2 S3 Battery Run Time (18650) High: 260 lumens, 10 hours Mid: 65 lumens, 40 hours Low: 22 lumens, 120 hours Supported Battery: 2 x 18650 (Built-in, non-replaceable) Maximum Beam Distance: 224 yards / 205 meters Maximum Beam Intensity: 10,500 cd Dimensions: 3.3 x 2.8 x 2 inches (83×70×52mm) Weight: 5.3 ounces (151 grams) Waterproof: IPX-8 standard (submersible up to 2 meters) Features: Designed for high risk industries, including mining, underground and offshore petroleum exploitation, petrochemical and chemical industries Intrinsically safe LED headlamp Explosion Group IIB, Operating Temp Class T5 (100°C) Featuring Advanced Temperature Regulation (ATR) technology to dynamically adjust output performance according to body temperature Utilizing a CREE XP-G2 S3 LED Powered by built-in 18650 battery/batteries for maximum output of 260 lumens USB magnetic charging cable for outputting 1000mA Intuitive user-interface with a button switch ensures easy one-handed operations Featuring 3 brightness levels and 2 special modes Featuring constant illumination/slow flashing red light Featuring power indicator and low battery alert Helmet mount included IP68 rating for dust and water resistance (3 meter submersible) 1.8 meter impact resistance

Read more less

Description Pop-up retailers, nightclub security personnel, and anyone else who needs to authenticate cash, IDs, or other documents will find the Tube UV Rechargeable Keychain Light from Nitecore to be a highly compact, lightweight tool for the job. It measures just 2.2 x 0.8 x 0.3", weighs under a half-ounce and is Micro USB rechargeable. The Tube UV has an output of 500mW UV emitter at 365nm wavelength, a lockout button to prevent it from being accidentally turned on and a sleek, sturdy polycarbonate housing. Its built-in lithium-ion battery can run the light continuously for up to one hour on a charge, and the light is equipped with overcharge, over-discharge and reverse polarity protection. The stainless steel key ring connector can lift 77 lb, so you can be sure the Tube will stay connected. Specifications Housing Material Polycarbonate LED 500 mW ultraviolet @ 365 nm Battery / Runtime Built-in rechargeable lithium-ion / 1 hour Dimensions 2.2 x 0.8" / 56.5 x 21.0 mm Weight 4.0 oz / 9.6 g

Read more less